EVA Foam Hardness Explained: The Asker C Scale and What It Means for Your Product

Specifying the right Asker C value early is one of the fastest ways to get an injection molded foam part that feels and performs as intended. Most molded EVA foam products fall between 35 and 75 Asker C: lower numbers give cushioning and rebound; higher numbers give structure, abrasion resistance, and dimensional stability. For product designers, Asker C is the number to use when writing a material spec, comparing quotes from molders, or checking incoming parts.

What Is the Asker C Hardness Scale?

The Asker C scale is a durometer hardness scale designed specifically for soft rubber, sponge, and plastic foams such as EVA. It rates a material from 0 to 100, where a higher number means the foam resists indentation more and feels firmer. When an EVA foam spec sheet lists “50C” or “50 Asker C,” it is reporting a reading on this scale.

EVA foam needs its own scale because of the indenter. The common Shore A gauge uses a small truncated cone that can puncture or crush open cells in a lightweight foam, which gives unstable readings. The Asker C gauge uses a rounded hemisphere that spreads the load over a larger area, so it reads the foam’s overall resistance rather than one cell wall.

Asker C is the same number PopFoam uses on its EVA foam technical data sheet, which lists standard compounds from 35 to 75 with a tolerance of ±2 points. 

How Is EVA Foam Hardness Measured on the Asker C Scale?

EVA foam hardness is measured by pressing a spring-loaded Asker C durometer into a flat foam sample and reading how far its rounded indenter sinks. Deep indentation gives a low number (soft foam); shallow indentation gives a high number (firm foam).

The Asker C gauge has a 5.08 mm diameter hemispherical indenter that travels up to 2.54 mm. Its spring pushes with about 55 g of force at a reading of 0 and about 855 g at a reading of 100. When you press the gauge into the foam, the foam’s resistance balances the spring load, and the indenter depth converts to a hardness value.

A reliable EVA foam hardness test follows a few rules:

  1. Use a thick enough sample. PopFoam’s technical data sheet specifies a 10 mm block for hardness readings. Thin parts let the indenter “feel” the table underneath, and readings come out artificially high.
  2. Test a flat, skin-on surface. Molded EVA has a denser outer skin than its core, so a molded surface and a cut surface of the same part can read several points apart. Agree with your supplier on which surface is measured.
  3. Press evenly and read at a consistent time. Readings drift down a few seconds after contact as the foam relaxes, so either record the peak value or read at a fixed interval. A durometer stand removes hand-pressure variation.
  4. Average several readings. Take at least three to five readings spread across the part, away from edges and ribs.
  5. Condition samples first. Test at room temperature after parts have cooled and stabilized from molding, since warm foam reads softer.

Following the same method on both sides of a supply relationship is what makes a ±2 Asker C tolerance meaningful. If your team and your molder measure differently, two “identical” parts can appear to be out of spec.

How Does Asker C Compare to Shore A and Other Hardness Scales?

Asker C reads higher than Shore A on the same EVA foam, so the two numbers are not interchangeable. A foam that measures roughly 35 Asker C reads only about 15 on Shore A, according to MISUMI’s hardness scale guide. Because Asker C spreads those low readings over more of its 0–100 range, it lets designers specify soft EVA foam far more precisely.

ScaleIndenterTypical MaterialsUse It For EVA Foam?
Asker C5.08 mm hemisphereSponge, closed-cell foam, EVA midsolesYes — the industry standard
Shore A35° truncated coneSolid rubber, urethane, TPEOnly for very firm or solid parts
Asker F25.2 mm flat cylinderVery soft foams and gelsFor ultra-soft foams below the Asker C range
Shore CNot the same as Asker CHarder rubbers and plasticsNo — easily confused with Asker C
Shore D30° sharp coneRigid plasticsNo

Indenter details: Checkline Asker durometer specifications.

Two cautions matter when you compare EVA foam specs from different suppliers:

  • “C” does not always mean Asker C. Shore C is a separate ASTM scale for harder materials. On an EVA spec, “55C” almost always means Asker C, but confirm it in writing.
  • Conversion charts are approximate. Foam density, skin thickness, and cell structure change how each indenter responds, so a Shore A-to-Asker C conversion is only a starting estimate. The most reliable approach is to measure the same sample on both scales, or simply specify Asker C from the start.

If you have an existing part spec’d in Shore A, an EVA injection foam molder like PopFoam can measure a sample of the current part in Asker C and match it, rather than relying on a chart.

What Asker C Hardness Should You Choose for Your EVA Foam Product?

Most EVA foam products land between 35 and 75 Asker C. Choose the low end (35–45C) when comfort and cushioning matter most, the middle (45–60C) when a part needs to cushion and hold its shape, and the high end (60–75C) when it must carry load, resist wear, or keep tight dimensions. For reference, Shoemakers Academy describes 25C as very soft, 55C as a standard shoe midsole, and 85C as wood-like.

Asker C RangeHow It FeelsTypical ApplicationsRelated PopFoam Projects
25–35CVery soft, high giveShock-absorbing pads, padding liners, comfort insertsSpa Pillow
35–45CSoft, cushionedExercise and yoga mats, protective padding, headgear linersMy Little Mat, LDR Head Gear
45–55CMedium, balanced cushion and supportMidsoles, anti-fatigue mats, grips, medical supportsStoic Standing Mat, TZ Medical Radial Runway
55–65CFirm, supportiveMassage and foam rollers, sports equipment, floatsAcumobility Ultimate Back Roller, The Orb Extreme
65–75CVery firm, structuralWheels and tires, plyo boxes, load-bearing partsRooBox Plyobox, molded EVA wheels and tires

These ranges are starting points, not rules. Product examples show the categories PopFoam molds; each project’s final hardness is set to its own performance requirements.

Three questions narrow the choice quickly:

  • What touches the part, and for how long? Constant skin contact favors softer foam. Brief or impact contact can go firmer.
  • What load does it carry? Parts that support body weight, roll, or bear point loads need higher Asker C to avoid bottoming out and permanent set.
  • How much should it bounce back? In PopFoam’s data, rebound falls from 60% at 35C to 32% at 75C, so softer foam returns more energy.

When two ranges both seem right, prototype at both. Holding a 45C and a 55C sample in hand usually settles the decision faster than any datasheet.

What Controls EVA Foam Hardness Besides Density?

EVA foam hardness is set mainly by the compound formulation, not by density alone. In PopFoam’s standard grades, hardness nearly doubles from 35C to 75C while density rises only about 16%, from 0.192 to 0.223 g/cm³. The difference comes from how the foam is formulated and molded.

The main levers used to hit a target Asker C value are:

  • Vinyl acetate (VA) content. Higher VA content generally makes EVA softer and more flexible; lower VA makes it stiffer.
  • Blowing agent and expansion ratio. More expansion creates more gas cells per volume and a softer feel.
  • Cross-linking level. More cross-linking increases firmness, heat resistance, and compression set performance.
  • Fillers and modifiers. Rubbers, elastomers and specialty additives tune hardness and rebound independently.

That last lever matters most for performance products. PopFoam’s specialty compounds show it clearly: a shock-absorbing grade measures 26C with just 8.2% rebound, while a high-resilience grade measures 43C with 70% rebound. Two foams of similar softness can behave in completely opposite ways, which is why you should always specify hardness alongside the performance you need.

Temperature also changes readings. EVA firms up in the cold and softens in heat, so products used outdoors or in cold water may need a cold-weather compound rather than a softer or harder grade.

Not sure which hardness fits your design? PopFoam formulates custom EVA compounds from 26C to 75C for each product. Talk to a PopFoam engineer about your hardness spec →

How To Specify EVA Foam Hardness for Your Next Product

The best EVA foam hardness spec states a target Asker C value, a tolerance, the test method, and the performance the part must deliver. Writing “55 ±3 Asker C, measured on the molded surface, with at least 45% rebound” gives a molder far more to work with than “medium-firm foam.”

A practical path from idea to production part looks like this:

  1. Define the job. List what the part must do: cushion, support, float, roll, grip, or protect. Note the temperature range and whether it contacts skin, children, or chemicals.
  2. Pick a starting range. Use the hardness table above to choose a 10-point band, such as 45–55C.
  3. Add the properties that matter. Pair hardness with rebound, tear strength, compression set, or buoyancy so the compound is tuned for performance, not just feel.
  4. Agree on the test method. Confirm Asker C (not Shore C), sample thickness, surface tested, and tolerance with your molder before tooling.
  5. Prototype and feel-test. Compare samples at two hardness levels in real use. Small changes of 5–10 points are easy to feel in hand.
  6. Lock the spec for production. Record the approved value and tolerance in your drawing or PO so every lot is checked the same way.

PopFoam selects the right Asker C value as part of its EVA foam injection molding process. Engineers start at the design stage, select or formulate a custom EVA compound for your hardness and performance targets, and build a process control plan around your tolerances. Our soft toughness® formula ensures a durable product that is virtually indestructible.

Want to go deeper? Download The Ultimate Design Guide for EVA Injection Foam Molding or browse EVA foam products PopFoam has brought to market.